HIMA F6706

HIMA F6706

Product Introduction The F6706 is SIL3 certified 2-channel intrinsically safe analog output module for HIMA HIMatrix safety system. It converts digital safety control commands from safety CPU into 4-20mA analog current signals for field valve positioners and analog actuators in hazardous explosive zones. It provides galvanic isolation and intrinsic safety energy limiting function, and carries out continuous channel diagnosis to detect wiring break, short circuit and signal fault.

Request Quote
Category:

Description

HIMA F6706

Technical Specifications

  • Product Type: Intrinsically safe analog output safety module
  • Channel Count: 2 analog output channels
  • Output Signal: 4-20mA current signal
  • Safety Certification: SIL3, ATEX / IECEx intrinsic safety certification
  • Bus Interface: HIMatrix safety backplane bus
  • Diagnosis: Wire break detection, short circuit detection, signal out of range monitoring
  • Protection Rating: IP20
  • Operating Temperature: -10 °C to +60 °C
  • Mounting: DIN rail rack mounting

Functional Features

  1. 2 independent intrinsically safe analog output channels output 4-20mA control signals.
  2. Intrinsic safety energy limiting circuit limits energy transferred into hazardous zone.
  3. High precision DAC converts digital command from safety CPU to analog current signal.
  4. Continuous channel self-diagnosis detects wiring break, short circuit and signal fault.
  5. Galvanic isolation separates safe side rack circuit and hazardous field circuit.
  6. LED indicators display module power, run and channel fault status.
  7. Fault signal transmission to safety CPU for fault logging and alarm.
  8. Overvoltage and overcurrent protection for each analog channel.
  9. Signal range validation rejects abnormal loop current value.
  10. Suitable for field devices installed in explosive classified hazardous areas.

Application Scenarios

  • Petrochemical plant hazardous area analog control valve output
  • Refinery reactor intrinsic safety analog actuator control
  • Offshore platform hazardous zone analog instrument control
  • Chemical plant tank farm intrinsically safe valve positioner control
  • High integrity pressure protection system analog control signal output

Material Composition

  • Housing: Flame-retardant polycarbonate plastic modular casing
  • Main PCB: FR4 high reliability printed circuit board with conformal coating
  • Conversion chips: High precision digital to analog converters
  • Isolation components: High isolation safety transformers and optocouplers
  • Energy limiting components: Precision resistors and zener diodes
  • Terminal block: Copper alloy spring cage wiring terminals
  • Backplane connector: Gold-plated copper contact pins

Structural Characteristics

  • Vertical modular rack unit compatible with HIMatrix F35 rack system.
  • Front panel equipped with LED status indicators for module and channel diagnostics.
  • Lower terminal block for hazardous area analog actuator wiring.
  • Rear gold-plated connector inserts into safety backplane bus.
  • Internal high isolation barrier separates safe side circuit and hazardous side circuit.
  • Dual independent diagnostic circuits run parallel for channel integrity verification.

Working Principle Safety CPU sends digital control value to F6706 module via safety backplane bus. High precision DAC converts digital value to 4-20mA analog current signal. The intrinsic safety energy limiting circuit restricts maximum voltage and current delivered to hazardous zone below ignition threshold of explosive gas mixture. Each channel continuously monitors loop current to detect wire break and short circuit. Fault information is sent to safety controller immediately when fault occurs.

Installation Requirements

  • Install module into HIMatrix F35 DIN rail rack inside non-hazardous control cabinet.
  • Use intrinsically safe approved shielded twisted pair cable for hazardous side wiring.
  • Separate hazardous side wiring and safe side wiring in different cable trays.
  • Follow ATEX and IECEx installation rules for hazardous area instrument wiring.
  • Verify sensor loop wiring polarity before power on.
  • Perform channel calibration and fault simulation test after installation.
  • Check backplane bus connection before power energization.

Usage Notes

  • Do not plug or unplug module when rack power remains active.
  • Do not apply voltage exceeding rated specification to analog channels.
  • Do not connect non-intrinsically safe equipment to hazardous side terminals.
  • Keep cabinet free of corrosive gas and oil mist.
  • Conduct periodic proof test according to SIL safety requirements.
  • Disconnect field wiring before insulation resistance test.
  • Replace module immediately when persistent hardware fault appears.

Related products