HIMA F6217
HIMA F6217 - Image 2

HIMA F6217

Product Introduction: F6217 is a SIL3 certified safety analog input module manufactured by HIMA for HIMax safety instrumented systems. It collects continuous analog measurement signals from field transmitters and converts analog signals into digital data for safety logic processing. This module executes signal filtering, channel diagnosis and signal validation, and transmits valid process data to the safety central controller. It serves for emergency shutdown, burner management and overpressure protection in high-risk industrial plants.

Request Quote
Category:

Description

HIMA F6217

Technical Specifications:

  • Power Supply: 24 VDC, 18 VDC to 32 VDC operating range
  • Analog Input Channels: 8 independent channels
  • Supported Signal Types: 4–20 mA, 0–20 mA, 0–10 V, ±10 V
  • Resolution: 12-bit ADC
  • Basic Accuracy: ±0.1% full scale at 25°C
  • Channel Isolation: 2500 V RMS galvanic isolation between field side and system backplane
  • Signal Update Cycle: 50 ms
  • Safety Response Time: Less than 450 ms
  • Operating Temperature: -40 °C to +70 °C
  • Storage Temperature: -40 °C to +85 °C
  • Relative Humidity: 5% to 95%, non-condensing
  • Safety Certification: IEC 61508 SIL 3, TÜV certified

Function Features:

  • Simultaneous sampling of 8 channels of analog field sensor signals
  • Programmable digital low-pass filter to suppress electromagnetic noise
  • Built-in channel fault diagnosis for wire break, short circuit and over-range signal
  • Signal validation and plausibility check for safety measurement loops
  • Galvanic isolation eliminates ground loop interference between field sensors and safety rack
  • Hot-swap capability during system operation without full rack shutdown
  • LED status indicators for power, module health and individual channel faults
  • Data transmission to HIMA safety CPU via internal system bus

Application Scenarios:

  • Oil and gas emergency shutdown systems
  • Chemical plant safety instrumented systems
  • Power plant boiler and turbine safety monitoring racks
  • Refinery process overpressure protection systems
  • Pharmaceutical reactor safety interlock control

Material Composition:

  • Main Substrate: Multilayer FR4 fiberglass printed circuit board with conformal coating
  • Core Components: High precision ADC chips, isolated operational amplifiers, safety microcontroller
  • Connectors: Gold-plated edge connector for rack backplane connection
  • Front Panel: Flame retardant black plastic with status LED windows
  • Passive Components: High precision metal film resistors, industrial grade capacitors, surge suppression diodes
  • Hardware Latches: Glass fiber reinforced plastic locking latches

Structural Features:

  • Standard Eurocard plug-in card form factor for HIMA HIMax rack installation
  • Front panel with LED indicators and module identification label
  • Gold-plated edge connector at the rear for backplane power and data bus
  • PCB surface protected by transparent conformal coating against moisture and dust
  • Plastic locking latch for secure insertion and extraction from rack chassis

Working Principle: Field analog signals from pressure, temperature and level transmitters enter the module through rack backplane terminals. Each channel passes signals through isolation circuits and programmable filters before analog-to-digital conversion. The onboard safety microcontroller validates signal values and checks for wire break or short circuit faults. Valid digital measurement data is transmitted to the safety CPU via internal backplane bus. If signal exceeds predefined safety thresholds, the module sends fault and process alarm information to the central controller for safety logic execution.

Installation Requirements:

  • Insert module into matched HIMA HIMax safety rack chassis
  • Wear anti-static wristband before handling the PCB module
  • Use shielded twisted pair cables for all field analog sensor wiring
  • Separate analog signal cables from high voltage power cables with minimum 30 cm clearance
  • Verify backplane connector cleanliness and no oxidation before module insertion
  • Implement reliable protective earth connection for the entire safety rack
  • Maintain cabinet ambient temperature within rated operating range

Usage Notes:

  • Configure channel signal type, scaling and filter parameters via HIMA HiDraw software before commissioning
  • Perform loop calibration for each analog channel during system startup
  • Complete safety proof test periodically according to site SIL maintenance schedule
  • Cut off rack power supply before removing module if hot swap is not required
  • Inspect gold-plated edge connectors for dust and corrosion during planned outages
  • Do not apply voltage or current exceeding channel rated input limits

Related products